Several scales can share the same notes — this ranks the closest matches over the last few seconds of playing.
Strum a full chord and let it ring — this reads the harmonic content across all six strings, not just the loudest note.
In Target Scale mode the root and scale tones are marked across the whole neck; whatever note you're currently playing lights up everywhere it falls, on every string.
Press Listen, then play a few notes.
Tap a string to hear its target note.
Press Listen, then hold a single note.
Load any song from your computer (MP3, WAV, M4A, OGG, FLAC). Drag across the waveform to pick a section and it loops; slow it down without changing the pitch; shift the key if your guitar is tuned differently. The song stays on this device — nothing is uploaded.
Load a song to start.
Space plays/pauses and ← → jump 5 seconds while this tab is open. [ and ] set the loop ends, L toggles the loop. A MIDI footswitch can do the same — see MIDI & Gear.
Fretnook listens to the whole song and works out its key, how far it sits from standard pitch (A = 440), and the chords as it goes. It is an estimate — great for finding your way around, not a substitute for your ears.
Anything that shows up as a sound input on your computer works: an audio interface, or a pedal/amp modeler with a USB audio connection (Boss, Line 6, Zoom, Neural DSP-style boxes and similar). Pick it from the Input menu at the top of the page, then press Listen — the effects happen on the pedal, and Fretnook records and monitors the processed sound.
No input open yet — press Listen.
Interfaces usually put a guitar on Input 1 (left). If you plug into Input 2, use Channel here. If the level looks low, press Auto level at the top of the page or raise Input trim. Turn off any “direct monitor” on the device if you hear the guitar twice.
Plug in a USB MIDI footswitch, pedalboard, or knob controller, press Connect, then use Learn next to any action and hit the pedal or turn the knob. Mappings are remembered on this computer.
MIDI is not connected. Press Connect MIDI (Chrome, Edge, or Opera on desktop/Android; iPhone/iPad Safari has no Web MIDI).
Last message: —
Arm a track, then hit Record — any other tracks with audio play back while you lay down the new take. Use headphones while layering so the mic doesn't pick up the playback. The metronome click is monitoring-only and is never captured onto a track. Tick Monitor to hear yourself through the armed track’s Sound Model (headphones only, or it will feed back). Takes are timed to line up with the tracks you were hearing; if an overdub still lands slightly early or late, nudge Sync (ms).
Program a beat, preview it, then bounce it onto an empty track like any other take — tempo follows the Metronome's BPM (Recorder tab).
Press Listen at the top first, then tap a style. To keep the beat, press Bounce to Track below.
Click steps below to build a pattern, then hit Play to preview.
A built-in synth and piano roll. Click the grid to place notes (drag to move, drag a note’s right edge to lengthen it, right-click or Delete Note to remove), press Play to loop it and jam along, then Bounce to Track to keep it as audio. Tempo follows the Metronome’s BPM (Recorder tab). Shaded rows are the key set on the Ear Trainer.
Click the grid to place notes, or pick a Starter.
Your own backing band. Pick a style and a chord progression and Fretnook builds drums and bass that follow the chords — or record your guitar first and press Listen & Suggest: Fretnook works out the tempo, key and chords of your take and fills in the chord box for you. Then Bounce puts each part (drums, bass, keys, horns) on its own empty track, lined up with your recording.
1. Listen to my track
Record a take on the Recorder tab, then come back here. Or skip this step and type your own chords below.
2. Pick the band
3. Hear it, then keep it
Pick a style and press Preview.
Piano, bass and horn sounds come from the FluidR3 GM soundfont (credit: Frank Wen; Creative Commons Attribution). They download the first time you use them, then work offline.
4 independent live loops, pedal-style: tap Record to start capturing from the mic, tap it again to close the loop and start it playing back immediately, then tap Overdub to layer another pass on top at the next time it loops around. Bounce any loop you like onto a Recorder track to make it a permanent part of the song.
Press Listen above first.
Build a song out of sections -- lay down a few bars on the Recorder tab, capture it as a section's source here, then Apply Arrangement to tile it across that section's length automatically. Sections play back on whichever track you captured them from, at the times they land at once applied, so a full song can come from just a handful of short takes.
Add a section, pick its source track, play/select the clip you want to repeat on the Recorder tab, then "Use Selected Clip".
Every track's clips, side by side, on one shared, real-time-accurate scale — unlike each track's own waveform strip on the Recorder tab (which stretches to fill its strip no matter how long that track actually is), so you can see exactly how parts line up across the whole song. Drag a clip left or right to move it; with Snap on, its start lands exactly on a beat or a bar at the current tempo. Trim, split and duplicate still happen on the Recorder tab.
Click a clip, then drag it to move it.
Record or import audio on the Recorder tab to see it laid out here.
Shapes and places whatever's already recorded on the Recorder tab — EQ, pan, reverb/delay sends, and per-track comp/gate, plus master bus mastering and the mix export. Level, mute, and solo still live over there.
Assign tracks to a group with each track's Group dropdown in the Mixer list above. A group's Level/Mute/Solo apply to every track routed into it, on top of that track's own fader -- handy for controlling a whole drum kit or backing-vocal stack with one fader. Soloing a group only affects tracks assigned to a group; ungrouped tracks keep following their own Mute/Solo as usual.
Export WAV bounces every track through this chain into one file, normalized and limited toward -1 dB peak. Export Stems instead renders each track separately (as it currently sounds, mute/solo respected) and zips them together, for finishing the mix elsewhere. Export Compact renders the same mastered mix as a small, share-ready file -- AAC (.m4a) or Opus (.webm) depending on what this browser can encode; it isn't literally an .mp3, but it's built for the same job: a quick, small file to text or upload. Downloads work when this page is open directly in your browser or installed as an app — not from a hosted preview link.
Final polish on the whole mix, after everything on the Mixer tab -- loudness metering, master-bus warmth, stereo width, a spectrum view, and hum/hiss cleanup. A/B toggles all of it off at once so you can compare against the untouched mix.
Loudness
Spectrum
Master Bus
Master EQ & Stereo
Noise / Hum
Compare
Film yourself playing and turn the finished mix into a music video. The camera's own mic is only used to line the picture up with your audio; the exported video always uses the mastered mix.
Camera
Preview
Turn the camera on to get started.
Video Lane
Click the lane to move the playhead. Click a clip to select it, then drag its left or right edge to trim. To cut between takes: Split at Playhead, select the new piece, and pick a different take under Clip Shows. Every take stays in sync with the song, so cuts never drift.
Takes
No video yet. Turn the camera on, then record a take or use Film to Mix.
Export renders the mastered mix with your edited video lane. It plays in real time, so a 4-minute song takes about 4 minutes. Keep this tab visible while it runs.